HOMS+OP+CxxD
8 Coaxial HD/SD/ASI In, Multiplexer, Upper/Lower CWDM
The HOMS+OP+ are active multiplexers. Active multiplexers combine the functions of electrical-to-optical (E-to-O) transmitters and passive CWDM multiplexers into one dense module. Multiplexers have four or eight HD/SD/ASI inputs that are converted into four or eight optical wavelengths. The optical wavelengths are then optically multiplexed onto one single-mode fiber optic cable.
For each type of multiplexer, there are four variations corresponding to the upper eight, lower eight, upper four and lower four wavelengths of the standard ITU-T G.694.2 16 wavelengths. An optical “express port” allows cascading individual products to completely fill (all 16) CWDM wavelengths, thereby providing the greatest level of coarse wave division multiplexing efficiency.
Features
- CWDM support according to ITU-T G.694.2 over the entire spectrum of 1270 to 1610 nm
- Expandable system in groupings of four or eight wavelengths, allowing cost-effective system configuration up to the complete 16-wavelength CWDM standard
- Electrical interface support: SD-SDI, HD-SDI, ASI, with automatic and manual reclocking rate setting (143, 177, 270, 360, 540, 1485 Mb/s) for SDI
- Occupies only two 6800+™ frame slots (out of 20) for either multiplexer or demultiplexer modules
- Optional CCS Navigator™ application for remote Ethernet PC-based status monitoring and control, and user-configurable NUCLEUS™ control panel control
- Third-party control through SNMP-based, published protocol
- Standard SC-type fiber optic connector
Images/Diagrams
Block Diagram
HOMS+OP+CL4D-CU4D-CL8D-CU8D
Back Module
| HOMS+OP |
 |
Specifications
Specifications and designs are subject to change without notice.
| Electrical Inputs | |
| Number of Inputs | 8 or 4 |
| Signal Type | HD-SDI, SD-SDI, ASI |
| Connector | BNC per IEC 169-8 |
| Impedance | 75 ohms |
| Return Loss | >17 dB (typical) from 5 to 1500 MHz |
| Cable Equalization | 0 to 300 m Belden 1694A for 270 Mb/s SDI
0 to 100 m Belden 1694A for HD |
| Optical Outputs | |
| Number of Outputs | 8 (dual mirrored outputs for the 4-wavelength version) |
| Signal Type | HD-SDI, SD-SDI, ASI |
| Connector | BNC per IEC 169-8 |
| Impedance | 75 ohms |
| Return Loss | >18 dB (typical) from 5 to 1500 MHz |
| Adjacent Channel Isolation | >30 dB |
| Non-adjacent Channel Isolation | >40 dB |
| Power Consumption HOMS+OP+Cx8D: 10.6 W HOMS+OP+Cx4D: 5.4 W | |
Ordering Information
| HOMS+OP+CL4D | Active 4-channel optical multiplexer, lower CWDM frequencies with optical output, HD/SD/ASI inputs |
| HOMS+OP+CL8D | Active 8-channel optical multiplexer, lower CWDM frequencies with optical output, HD/SD/ASI inputs |
| HOMS+OP+CU4D | Active 4-channel optical multiplexer, upper CWDM frequencies with optical output, HD/SD/ASI inputs |
| HOMS+OP+CU8D | Active 8-channel optical multiplexer, upper CWDM frequencies with optical output, HD/SD/ASI inputs |
| Cable Options | |
| OP+CBL+1M-SCPC | Single-mode fiber cable, 1 meter, SC/PC male termination |
| OP+CBL+1M-STPC | Single-mode fiber cable, 1 meter, ST/PC male termination |
| OP+CBL+5M-SCPC | Single-mode fiber cable, 5 meter, SC/PC male termination |
| OP+CBL+5M-STPC | Single-mode fiber cable, 5 meter, ST/PC male termination |
Sales Contacts
- North America +1 800 231 9673
- Caribbean and Latin America +1 786 437 1960
- Europe and Africa +44 118 964 8200
- Middle East and South Asia +971 4 433 8250
- Asia, Pacific Rim +852 2776 0628
