Adobe PDF Icon Print Friendly Version

CTT6800+SDT, +HDT

JPEG 2000 Compressed Transport Transceiver

The CTT6800+ is ideal for applications requiring compressed transport of video, audio and data signals. Utilizing an advanced JPEG 2000 compression codec, the CTT6800+ can encode and decode baseband media to/from a 270 Mb/s DVB ASI transport stream. The CTT6800+ supports the following signal formats:

  • SDI (270 Mb/s SMPTE 259M or 1.5 Gb/s SMPTE 292M)
  • Four AES audio pairs
  • LTC
  • GPI
  • Dolby® metadata

Features

  • Configurable as either a JPEG2000 encoder or decoder; this allows switching of two CTT6800+ modules, operating as an encode/decode pair, to transport content in either direction
  • Compression of baseband media utilizing advanced JPEG2000 codec, including 270 or 1.5 Mb/s SDI, AES and embedded audio, LTC, GPI and serial Dolby® metadata with encoding onto a 270 Mb/s DVB-ASI transport stream
  • Encoding and decoding of up to four lines of user-selectable ancilliary data
  • Automatic or user-selectable video compression data rates of up to 200 Mb/s
  • Onscreen display for simplified setup and configuration
  • Supports Q-SEE™ thumbnail and alarm monitoring
  • Remote control and monitoring via CCS™ or SNMP

Images/Diagrams

Block Diagrams

CTT6800+ – JPEG 2000 Compressed Transport Transceiver (Receiver Mode)

CTT6800+Receiver-BD.jpg

CTT6800+ – JPEG 2000 Compressed Transport Transceiver (Transmitter Mode)

CTT6800+Transmitter-BD.jpg

Back Module

CTT6800+BM.jpg

Specifications

Specifications and designs are subject to change without notice.

ASI Input
Standard 
ConnectorBNC (IEC 169-8)
Impedance75 ohms
Return Loss>18 dB from 5 to 270 MHz
Equalization>23 dB Belden 8281 cable
Minimum Sensitivity200 mV
Maximum Input Voltage800 mV pk-pk
Data RateUp to 270 Mb/s

ASI Output
Standard
ConnectorBNC (IEC 169-8)
Impedance75 ohms
Return Loss>18 dB, typical, from 5 to 270 MHz
Signal Level800 mV ±10%
D.C. Offset0 V ±0.5 V
Rise and Fall Time400 ps to 1500 ps (20% to 80%)
Overshoot<10% of amplitude
Jitter<0.2 UI (pk-pk)
Data RateUp to 270 Mb/s

HD-SDI Input
StandardSMPTE 292M, 1080i/59.94, 1080i/50, 720p/59.94, 720p/50, 720p/23.98
ConnectorBNC (IEC 169-8)
Impedance75 ohms
Return Loss>18 dB (typical) from 5 to 1485 MHz
EqualizationAdaptive cable equalization for up to 328 ft (100 m), typical, of Belden 8281 co-axial cable or 492 ft (150 m), typical, of Belden 1694A coaxial cable

SD-SDI Input
StandardSMPTE 259M-C, 270 Mb/s, 525/625
ConnectorBNC (IEC 169-8)
Impedance75 ohms
Return Loss>18 dB from 5 to 270 MHz
Equalization>23 dB Belden 8281 cable

HD-SDI Output
StandardSMPTE 292M, 1080i/59.94, 1080i/50, 720p/59.94, 720p/50, 720p/23.98
Quantization10 bits
ConnectorBNC (IEC 169-8)
Impedance75 ohms
Return Loss>18 dB, typical, from 5 to 1485 MHz
Signal Level800 mV ±10%
D.C. Offset0 V ±0.5 V
Rise and Fall Time<270 ps
Overshoot<10% of amplitude
Jitter<135 ps pk-pk

SD-SDI Output
StandardSMPTE 259M-C, 270 Mb/s, 525/625
Quantization10 bits
ConnectorBNC (IEC 169-8)
Impedance75 ohms
Return Loss>18 dB, typical, from 5 to 270 MHz
Signal Level800 mV ±10%
D.C. Offset0 V ±0.5 V
Rise and Fall Time400 ps to 1500 ps (20% to 80%)
Overshoot<10% of amplitude
Jitter<0.2 UI (pk-pk)

GPIO Interfaces
GPI Inputs4
Internally pulled HIGH
External contact closure to ground to trigger
GPI Outputs4
TTL compatible
Sink 64 mA, source 32 mA
ConnectorDB-9

LTC Input
ElectricalDifferential Balanced
StandardSMPTE/EBU LTC 24/25/30 drop/no-drop
ConnectorScrew terminal
ImpedanceHi-Z (>30 k ohms) or 600 ohms, jumper selectable
Sensitivity500 mV pk-pk
CM Range±10 V
CMRR40 dB at 60 Hz

LTC Output
ElectricalDifferential Balanced
StandardSMPTE/EBU LTC 24/25/30 drop/no-drop
ConnectorScrew terminal
ImpedanceLow-Z (<25 ohms per side) or 600 ohms, jumper selectable
Level3.9 V pk-pk nominal to 1 k ohm, (low-Z output)
2.5 V pk-pk nominal to 1 k ohm, (600 ohms output)
Transition Time40 us ±4 us measured at 10% and 90% amplitude

Unbalanced AES Inputs
Number of Inputs4
StandardAES3, SMPTE 276M
ConnectorBNC (IEC 169-8)
Sensitivity<100 mV pk-pk (50 mV pk-pk typical)
Impedance75 ohms
Return Loss<-25 dB, 0.1 to 6 MHz (<-35 dB typical)
Input Audio Rate16 to 96 kHz

Unbalanced AES Outputs
Number of Outputs4
StandardAES3, SMPTE 276M
ConnectorBNC (IEC 169-8)
Impedance75 ohms
Return Loss<-25 dB, 0.1 to 6 MHz (<-35 dB typical)
Jitter<±4 ns, peak value
DC Offset0 ±50 mV
Rise and Fall Time30 ns to 44 ns (10% to 90%) (33 ns typical)

Dolby® E Metadata (RS-232/422)
ElectricalDifferential Balanced
StandardElectrical specification EIA-232C
ConnectorDB-9
232/422 switchable

Ordering Information

CTT6800+HDTJPEG2000 compressed transport transceiver module; HDTV/SDTV signal format support; includes front module and triple-width back module; requires 3 available 6800+ slots

CTT6800+SDTJPEG2000 compressed transport transceiver module; SDTV signal format support; includes front module and triple-width back module; requires 3 available 6800+ slots

CTT68+SD-UG-HDField upgrade for CTT6800+SDT; feature upgrade to CTT6800+HDT functionality; software activation key upgrade
Sales Contacts
  • North America +1 800 231 9673
  • Caribbean and Latin America +1 786 437 1960
  • Europe and Africa +44 118 964 8200
  • Middle East and South Asia  +971 4 433 8250
  • Asia, Pacific Rim +852 2776 0628